Back to Blog
Loxone dimmer5/20/2023 Only mount the device on a horizontal DIN rail to ensure heat dissipation by convection. This device must be mounted on a DIN rail in an electrical distribution enclosure to ensure protection against contact, water and dust. Installation must be carried out by a qualified electrician in accordance with the applicable regulations. Smart Actuators support dynamic fade times and can only be used with the Lighting Controller. Use device with Standard Actuator(s) or Smart Actuator(s) When selected, you will be notified via System Status or the Mailer if the device is no longer available or goes offline. Save into the Miniserver, in order to pair the Extension.Īfterwards the program must be loaded from the Miniserver to transfer the actual serial number of the Extension into the program. This can only be used if there is only one Extension of the same type. Specifies the serial number of the device.įor Extensions: Enter 'Auto' to automatically pair an extension with unknown serial number. This can be due to short-circuits, overloaded switching loads or too high an ambient temperature. If the CPU temperature reaches a critical point, the outputs of the device are switched off. If the motor is not suitable, this can damage both the motor and the Dimmer Extension! Only use this if you have experience with speed control of motors by phase cutting and if it is known that the motor type used can be controlled by leading edge phase cut and that no dangerous voltage peaks occur. However, only certain motors are suitable for this. The Dimmer Extension can also be used for speed control of motors via leading edge dimming. In such a case, use other lamps or a higher number per channel, or switch them off via an additional relay contact. However, some low-power LED lamps are so sensitive that this can cause occasional flashing or slight glowing. The voltage disappears with even a low load, as there is virtually no power available here. This results in a voltage being measurable at the outputs even when the outputs are switched off, especially without a load. The outputs of the Dimmer Extension are equipped with capacitors for interference suppression. If possible, test different LED luminaires for dimmability before purchasing a large quantity. It is advisable to use high-quality luminaires, which guarantee consistent quality and long-term availability. There may also be batch-related differences in LED lamps. However, characteristics such as the dimming curve, dimming range, and flicker-free dimming can differ for every luminaire. In principle, all line voltage LED luminaires marked as dimmable can be dimmed with the Dimmer Extension. However, for low-voltage halogen lamps, the transformer must be dimmable. Generally, incandescent lamps are always dimmable, even if they are not labeled as dimmable. Halogen lamps can also be categorized as incandescent lamps and are an alternative when the highest quality of light is desired and the energy consumption is acceptable. Of all luminaires, incandescent lamps are the easiest to dim. If in doubt, the manufacturer of the illuminant can provide information on the load characteristics (whether inductive or capacitive) and the recommended dimming method. The ballasts, LED drivers, electronic transformers etc. **A magnetic transformer must be loaded with at least 80% of it's capacity! *The sum of the nominal load of the ballasts, LED drivers or transformers is relevant, not the nominal load of the actual light. Low voltage halogen lamps with magnetic transformer (MLV) Line voltage LED lamps (retrofit, LED bulbs) Low voltage halogen lamps with electronic transformer (ELV) Only use luminaires that marked as dimmable! Please observe the recommended dimming type and load limits! The Extension starts after switching on the power supply, and the status LED will flash orange after a short time when the connection to the Miniserver is established. However, a single-phase supply is also possible.Įnsure sufficient air circulation to allow the generated waste heat to dissipate, especially at high workloads. In case of large loads or multiple dimmers, it is advisable to spread the load across several phases as shown in the wiring example. The Dimmer Extension is installed on a DIN rail in a suitable enclosure.Ĭonnect the power supply and Link communication to the Miniserver.Ĭonnect the loads to the outputs as shown in the example above. The Dimmer Extension features 4 channels for dimming suitable line voltage lights.Įach channel can be set to trailing edge or leading edge dimming, the Dimmer Extension is thus suitable for resistive (incandescent), capacitive (ELV) and inductive (MLV) loads.Īdditionally, 8 digital inputs for 24V are available.ĭatasheet Dimmer Extension 120V Table of Contents
0 Comments
Read More
Leave a Reply. |